Mirrored vector
A vector shape drawn once and repeated by symmetry. Edit one source piece and every copy follows, either rotated around the centre (radial) or flipped across the vertical axis (bilateral).
In a formula, a node is called by its name in the layers panel: Mirroredvector1.mirrorAxis
Properties
mirrorAxisString#
How the source piece is repeated: radial or bilateral.
radial rotates copies of the source piece around the centre, as many as sectors says. bilateral draws the source piece once and adds its mirror image across the vertical axis through the centre; sectors does not apply.
Default 'radial' · 'radial' | 'bilateral' · animatable
sectorsInteger#
Amount of copies of the source piece around the centre (radial mode only).
Default 5 · 3 – 16 · whole numbers · animatable
spreadAngleNumber#
Total angle, in radians, that the copies cover around the centre.
The default 2π (about 6.283) closes the circle. A smaller value packs the same number of copies into a fan, each one spreadAngle / sectors apart, and leaves the rest empty.
Default 6.2832 · radians · animatable
sourceVerticesString#
Points of the source piece, as a flat list of x, y pairs in pixels inside the node.
read-only
sourceSegmentsString#
Segments of the source piece, as a flat list of index pairs: the start point and the end point of each, counted in sourceVertices.
read-only
sourceTangentsString#
Curve handles of the source piece, four numbers per segment: x, y of the handle at its start, then x, y of the handle at its end.
Positions are in pixels inside the node. A handle of 0, 0 means no handle there, so that end of the segment is straight.
read-only
sourceLoopsString#
Which source segments are chained into a path: a list of paths, each a list of indices into sourceSegments.
read-only
Transform from Transform
xNumber#
Horizontal position of the node's origin, in pixels from its parent's origin.
The origin is the point the node turns and scales around (the small circle you can drag on the canvas). Setting x moves the whole node so that its origin lands there.
pixels · animatable
yNumber#
Vertical position of the node's origin, in pixels from its parent's origin. Larger values are lower.
pixels · animatable
wNumber#
Width of the node in pixels.
On a skewed node this is the width you see on screen, not the width of the box before the skew.
0 – ∞ · pixels · animatable
rotationNumber#
How far the node is turned around its origin, in degrees. Positive values turn it clockwise.
degrees · animatable
skewNumber#
How far the node is slanted along its own horizontal axis, in degrees.
Accepted values are -89 to 89, and 0 means no slant. The node stays anchored at its origin. A skewed node reports a wider w, because w is the width you see on screen. Bones and skeletons ignore skew.
degrees
Fill from Fill
fillsPaint[]#
The list of paints that fill the inside of the shape.
Paints are drawn in list order, so each one covers the one before it. A new shape starts with one grey solid paint. An empty list leaves the shape unfilled. Read a single paint with fills[0].
animatable
Stroke from Stroke
strokesPaint[]#
The list of paints that colour the outline.
A new shape has no strokes, so no outline is drawn until you add one. Paints are drawn in list order.
animatable
strokeWeightStrokeWeight#
Thickness of the outline in pixels.
The default is 1. A weight of 0 draws no outline.
0 – ∞ · animatable
strokePositionString#
Where the outline sits relative to the edge of the shape: INSIDE, CENTER or OUTSIDE.
CENTER puts half of the weight on each side of the edge. INSIDE and OUTSIDE put all of it on one side.
Default 'CENTER' · 'INSIDE' | 'CENTER' | 'OUTSIDE' · animatable
strokeJoinString#
How the outline turns at a sharp corner: MITER (pointed), ROUND or BEVEL (cut flat).
A MITER corner sharper than strokeMiterAngle is cut flat like a BEVEL.
Default 'MITER' · 'MITER' | 'ROUND' | 'BEVEL' · animatable
strokeMiterAngleNumber#
The sharpest corner angle, in degrees, that still gets a pointed MITER join.
Corners sharper than this are cut flat. A larger value cuts more corners. The default is 26 and the lowest accepted value is 8. It has no effect when strokeJoin is ROUND or BEVEL.
Default 26 · 8 – 180 · animatable
dashCapString#
Shape of the ends of each dash in a dashed outline: butt (flat), round or square.
This is separate from strokeCap, which shapes the two ends of the whole path. It only shows when the outline is dashed.
Default 'butt' · 'butt' | 'round' | 'square' · animatable
Appearance from Appearance
opacityNumber#
How opaque the node is, from 0 (invisible) to 1 (solid).
It applies to the node and everything inside it. It multiplies with the opacity of each paint.
Default 1 · 0 – 1 · animatable
blendModeBlendMode#
How the node mixes its colours with what is behind it, for example MULTIPLY or SCREEN.
NORMAL just draws over the background. The other values are NORMAL, PASS_THROUGH, MULTIPLY, SCREEN, OVERLAY, DARKEN, LIGHTEN, COLOR_DODGE, COLOR_BURN, HARD_LIGHT, SOFT_LIGHT, DIFFERENCE, EXCLUSION, HUE, SATURATION, COLOR and LUMINOSITY.
Default 'NORMAL' · animatable
visibleBoolean#
Whether the node is drawn. Set it to false to hide the node and everything inside it.
A hidden node still exists, so formulas can read and change its properties.
Default true · animatable
Shape animation from Shape animation
Node methods every node has them
is(typeOrTag: String) → Booleanmethod#
True when the node is of this type or carries this tag.
typeOrTagA node type such as 'RECT', or a tag.
clone() → Nodemethod#
Makes a copy of the node and returns it, so code can place and change the copy.
destroy()method#
Marks the node for removal; it is taken out of the scene at the end of the frame.
appendChild(child: Node) → Nodemethod#
Moves child into this node as its last child and returns it.
insertBefore(newChild: Node, refChild: Node | null) → Nodemethod#
Moves newChild into this node, just before refChild, and returns it.
refChildThe child to insert before; null appends at the end.
removeChild(child: Node) → Nodemethod#
Takes child out of this node and returns it.
replaceChildren(...nodes: Node)method#
Replaces all of this node's children with the given nodes, in that order.
insertAdjacentElement(position: 'afterbegin' | 'beforeend', element: Node) → Node | nullmethod#
Moves element into this node, as its first or last child.
position'afterbegin' puts it first, 'beforeend' last. Any other position does nothing and returns null.
on(event: String, fn: Function)method#
Calls fn each time fire(event) is called on this node. These are the node's own messages, not the Events panel: a click does not reach on('click').
off(event: String, fn: Function)method#
Stops calling fn for event.
fnThe same function that was passed to on.
fire(event: String, ...args: any)method#
Calls every function added with on(event) on this node, in the order they were added.
...argsPassed on to every listener.